How to Set up a Tub: Set Up an Acrylic Bathtub as Well as Bathtub Surround
How to Set up a Tub: Set Up an Acrylic Bathtub as Well as Bathtub Surround
Blog Article
Just how do you actually feel with regards to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Mounting a bathtub isn't exactly rocket science, but it does need solid plumbing, carpentry, as well as occasionally, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably hard task. If the old bathtub is easily obtainable, the task can relocate easily; if you need to open up a wall surface to get rid of the old bathtub and also place the brand-new bathtub, the task is much harder. In either case, the project is within a home handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and set in the new one. Ensure you have actually certified on your own for the work and also fit trying it. Rather than working with a contractor to take over a halfway-completed project, it is better to consider employing one before you begin. Chances are you may need a professional plumber to make tube connections.
This article will help you install a new bathtub in your bathroom if you have actually currently acquired a brand-new bathtub and do not require to transform the setup of your previous water pipelines.
Your tools and material checklist should consist of the following:
Planning for the Installment
To start with, the sustaining structure provided with the bathroom needs to be fitted (if called for) according to the supplier's guidelines. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is essential to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is likewise sensible to fit a supporting plate under the taps device to stop pressure on the tub.
Fit the versatile tap connectors to the bottom of the two faucets making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you utilize every one of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom ought to now be ready to be suited its last setting.
Removing Old Taps
If you need to change old faucets with new ones as a part of your installation, then the first thing you ought to do is detach the water supply. After doing so, activate the faucets to drain pipes any water continuing to be in the system. The procedure of removing the existing faucets can be fairly troublesome as a result of the restricted access that is frequently the situation.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the taps. Have a fabric ready for the staying water that will originate from the pipes. When the supply pipelines have been eliminated, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from transforming during this procedure. When the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Setting up the Tub
Using the two wood boards under its feet, put the bath tub in the required placement. The wooden boards are handy in evenly spreading out the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 small factors.
The next goal is to make certain that the bathtub is leveled all round. This can be accomplished by checking the spirit level and also adjusting the feet on the tub till the spirit level checks out degree.
To install faucets, fit the bottom of the outermost flexible tap adapter to the appropriate supply pipe by making a compression sign up with; after that do the same for the other faucet.
Switch on the water system as well as examine all joints and new pipework for leakages and also tighten them if necessary. Fill up the bath tub as well as also inspect the overflow electrical outlet and also the normal outlet for leaks.
Lastly, deal with the bath paneling as described in the maker's user's manual. Tiling and also sealing around the bathtub ought to wait up until the bath tub has actually been made use of at least once as this will settle it into its final setting.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic adapter to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap and the various other end gives a link to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly require decreasing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin ensuring that the washing machines are in place between the faucet and the sink. Secure the tap in place with the manufacturer supplied backnut. As soon as the faucet is safely in place, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with typical tap ports. The previous type should be connected to the faucet finishes initially, tightening only by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bathroom satisfies the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the fitting can relocate sufficient to break a rigid seal, creating the water to pass through the wall between the bathroom as well as the tiling, resulting in difficulties with wetness as well as possible leakages to the ceiling below.
You can pick from a range of coloured sealants to assimilate your components and installations. They are offered in tubes and cartridges, and also are capable of sealing voids as much as a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to always load the bathtub with water prior to sealing, to permit the motion experienced when the tub remains in use. The sealer can crack rather early if you do not take into account this motion prior to sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily offered on the market. It is a good idea to fit the tiles utilizing water-resistant or water resistant glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you appreciate reading about How to Install a Bathtub Yourself? Give a remark further down. We'd be interested to listen to your thinking about this review. In hopes to see you back again later on. Liked our write-up? Please share it. Let someone else locate it. Bless you for your time. Kindly visit our site back soon.
Book Today
Report this page